Works - DRGW Dynamometer Car #10 - 02 [Works_MOW Equipment]
: bay window parts for DRGW 10
I shove and polished the bay window parts from an Atlas jewel case box.
The other parts I used for the roof and sides are;
・Smoke stack from Sunrise dead stock parts #N-1001,
・Ventilators shoved from parts in American Limited Models Passenger Car Roof and Underframe Accessories,
・Exhaust pipe and muffler from 1.2mm aluminum pipe and 0.8mm brass rod,
・Roof-walk by MTL #499 55 910 as usual,
・Ladders by GOLD MEDAL MODELS #160-25, also as usual,
・Stirrups by Blma #60, also as usual,
I shove and patched one of the original ventilators. I gave up shaving the sill of the car because the underframe by MTL where underframe equipment hung would show up if I do that.
: exhaust pipe and muffler on the roof
bay windowは、Atlas製品が入っていたプラスティックケースのふたから削り出した。それ以外に、車体に取り付けたパーツは次の通り、
・煙突はSunriseの絶版パーツ#N-1001をそのまま使用。
・ベントキャップはAmerican Limited Modelsの客車床下機器パーツセットに付属のものを削り使用。
・排気管とマフラー(おそらく発電機のもの)は外径1.2ミリのアルミパイプと0.8ミリの真鍮線で制作。
・屋根歩み板はいつものようにMTL製パーツ#499 55 910をそのまま使用。
・はしごや手すりもいつも通りGOLD MEDAL MODELS製#160-25・Blma製#60をそのまま使用。
その他、車体廻りでは屋根に表現されているベンチレーターを1カ所削ったのみである。床下機器を取り付けるMTL製の台枠が丸見えになるので、裾は今回製品のままとした。
I shove and polished the bay window parts from an Atlas jewel case box.
The other parts I used for the roof and sides are;
・Smoke stack from Sunrise dead stock parts #N-1001,
・Ventilators shoved from parts in American Limited Models Passenger Car Roof and Underframe Accessories,
・Exhaust pipe and muffler from 1.2mm aluminum pipe and 0.8mm brass rod,
・Roof-walk by MTL #499 55 910 as usual,
・Ladders by GOLD MEDAL MODELS #160-25, also as usual,
・Stirrups by Blma #60, also as usual,
I shove and patched one of the original ventilators. I gave up shaving the sill of the car because the underframe by MTL where underframe equipment hung would show up if I do that.
: exhaust pipe and muffler on the roof
bay windowは、Atlas製品が入っていたプラスティックケースのふたから削り出した。それ以外に、車体に取り付けたパーツは次の通り、
・煙突はSunriseの絶版パーツ#N-1001をそのまま使用。
・ベントキャップはAmerican Limited Modelsの客車床下機器パーツセットに付属のものを削り使用。
・排気管とマフラー(おそらく発電機のもの)は外径1.2ミリのアルミパイプと0.8ミリの真鍮線で制作。
・屋根歩み板はいつものようにMTL製パーツ#499 55 910をそのまま使用。
・はしごや手すりもいつも通りGOLD MEDAL MODELS製#160-25・Blma製#60をそのまま使用。
その他、車体廻りでは屋根に表現されているベンチレーターを1カ所削ったのみである。床下機器を取り付けるMTL製の台枠が丸見えになるので、裾は今回製品のままとした。
2011-06-03 11:34
コメント(0)
トラックバック(0)
コメント 0